Aerospace machining is often treated as a different planet from everyday CNC work. In practice the overlap is large: the mills, the tolerances, and the measuring equipment resemble precision commercial work, and what changes is the record around the part. When you buy aerospace components through an online CNC machining supplier you are really buying four things at once - the machined part, the material traceability, the inspection evidence, and the change control that survives an audit.
- Materials to name: 7075-T6 and 2024-T351 aluminum, Ti-6Al-4V, 17-4 PH stainless, and Inconel 718 where the temperature calls for it.
- Tolerance envelope: ±0.003 mm on milled and turned features, ±0.002 mm on precision-ground surfaces, with capability Ppk ≥ 1.67 at the initial study on key characteristics and Cpk ≥ 1.33 on general characteristics. Capability is reported per characteristic: every report names the feature, its tolerance band, the sample size, the sigma method, and the study window.
- Proof to require: a mill certificate with heat number, a CMM or instrument report, a first-article report for the first lot, and a written deviation record.
- AS9100: the aerospace quality framework. Verify how the supplier documents traceability and change control, and check the base quality certifications underneath.
When does an aerospace part need more than a standard machining quote?
Most aerospace machining is build-to-print. Your organization holds the design, the stress analysis, and the qualification data; the machine shop buys the alloy, machines the geometry, and measures the result. What makes the transaction different is the burden of proof. A component destined for a structural or flight application carries a paper trail - material traceability to a heat number, inspection data tied to the drawing revision, and a record of every deviation.
The practical changes are traceability, change control, and documentation. An aerospace drawing often names an alloy temper or a heat-treated condition, expects the supplier to machine to the drawing revision you released, and assumes no material substitution happens without written approval. The supplier should also know how to notify you when a process changes, because a silent switch of barstock source or coating can invalidate data you have already qualified.
None of this requires exotic machinery. It requires the disciplines that an online CNC machining service can apply to a remote buyer as easily as to a local one: the drawing is the contract, incoming material is verified before cutting, and deviations are recorded instead of smoothed over. Those are the habits to probe in the first technical review.
Which aerospace alloys should your drawing specify - and why?
Five alloys cover the majority of build-to-print aerospace machining. The useful choice is not the most expensive material that could work, but the alloy and condition that match the function and the qualification you already hold. The table below summarizes where each one shows up and what to watch when you machine it.
| Alloy | Typical application | What to specify |
|---|---|---|
| 7075-T6 aluminum | Structural brackets, frames, fittings | High strength-to-weight ratio. The -T6 temper is standard; watch for stress-corrosion sensitivity in thick sections and confirm the grain direction requirement on the drawing. |
| 2024-T351 aluminum | Airframe components needing toughness and fatigue resistance | Good damage tolerance but lower corrosion resistance than 7075; specify the temper and any surface protection in the note. |
| Ti-6Al-4V (Grade 5) | Highly loaded structural parts, brackets, fasteners | Strong, light, and corrosion resistant but slow to machine. Budget longer cycle times and expect a premium over aluminum. |
| 17-4 PH stainless | Actuator components, landing-gear parts, fasteners | Strength comes from the precipitation-hardening step; name the condition (H900 or H1025 is common) so the certificate proves it. |
| Inconel 718 | High-temperature and turbine-adjacent hardware | Severe work hardening and low machinability make it expensive; reserve it for parts that genuinely see the temperature. |
Write the alloy, temper, and certificate expectation into a drawing note - for example 7075-T6 aluminum with a mill certificate required - rather than leaving the material to the purchaser to infer. When the certificate is part of the part specification, the quote reflects the correct material cost on day one and there is no argument later about whether a substitute grade would have done.
How do you verify that the alloy loaded on the machine matches the drawing?
A certificate that never leaves an email folder is decoration. The control that matters happens before chips fly: incoming material is quarantined on arrival, the certificate heat number is matched against the supplier markings on the stock, and an alloy check is run before release to a machine. XRF verification is common practice at precision shops because a paper trail alone cannot catch a mislabeled bundle.
You can audit this from a distance with three questions. First, does the shop keep a mill certificate per heat number and link the finished parts back to that lot? Second, is incoming material physically verified against the certificate, or only matched on paper? Third, can the supplier produce the certificate for the exact lot that ships to you, rather than a generic type certificate that could describe any bar of that alloy?
Require the certificate, with its heat number, to be attached to the first-article report. After that, lot-level records are the trail you need if a part fails in service - and in aerospace, a missing heat number is not a paperwork annoyance, it is a fleet-wide investigation trigger.
What tolerance can an aerospace machining drawing realistically demand?
Aerospace drawings are often assumed to need tolerances beyond what any process holds reliably. The realistic production envelope is the same one used in serious precision work everywhere: ±0.003 mm for milled and turned features, and ±0.002 mm for precision-ground surfaces that must seat or seal. What changes is the acceptance standard - capability Ppk ≥ 1.67 at the initial study on key characteristics and Cpk ≥ 1.33 on general characteristics. Capability is reported per characteristic: every report names the feature, its tolerance band, the sample size, the sigma method, and the study window., demonstrated from the first article forward, rather than a handful of parts that happened to land inside the band.
Tighten only the features that earn it. A bore that locates a bearing or a surface that seals justifies ±0.003 mm or a grinding operation; a cosmetic flange face does not. Drawings that scatter tight callouts across every feature multiply inspection cost and quoting conservatism without improving the part, and they slow every future engineering change.
Plan for measurement as you write the callouts. A ±0.003 mm claim is verified against the drawing datum reference frame, typically on a CMM, not with hand tools on the shipping bench. If the drawing is built on GD&T - and aerospace drawings usually are - ask how the supplier will measure position and form, not just size, and put the inspection method into the order.
Agree which drawing standard governs before cutting. Many aerospace drawings are built to ASME Y14.5, and a shop that quotes position and profile callouts should state that it measures them to that standard on its CMM. When the drawing and the standard are named together in the order, the acceptance test stops being a matter of opinion.
What documentation should travel with an aerospace lot?
Agree the document package before you order, not after the first lot is airborne. A practical set for build-to-print aerospace machining:
- Material certificate for each heat number used, naming the alloy, temper, and condition on your drawing.
- Certificate of conformance confirming the parts were machined, inspected, and finished to the drawing revision you released.
- Dimensional report from the method the drawing names - CMM reports for GD&T callouts, roughness data where Ra is specified.
- First-article report for a new part, plus SPC data on key characteristics where the program requires it.
- Deviation or non-conformance record for anything that left nominal, agreed before shipment rather than discovered at your incoming inspection.
The format matters as much as the list. Decide whether you need a report per lot, a shared data sheet, or PPAP-style documentation, because records assembled to a standard are cheap when planned and expensive when reconstructed. The quality page on this site lists the CMM, surface, and vision instruments behind the reports and how data is linked to each lot.
The documentation load does not stop at the first lot. Keep the approved FAI and the certificate from the first article as the reference sample, and require the same configuration to be reported on repeat lots until you formally reduce the layout. A shop that documents every lot to the same standard makes your incoming inspection faster and your audit trail cleaner.
What does AS9100 mean for an online machining supplier - and what should you actually check?
AS9100 is the quality management standard that aerospace primes and tier suppliers expect their component makers to operate under or align with. For a build-to-print machine shop the relevant content is familiar territory: document control, controlled purchasing, lot traceability, change and deviation notification, and calibration and competence records. A supplier aligned with that framework behaves predictably when a drawing changes or a lot fails.
An online CNC machining service does not need to be the design holder. You keep the design and the qualification data; the shop is accountable for the quality of the purchased parts and services it provides. When you evaluate a supplier for aerospace work, ask how its processes line up with AS9100 expectations, and verify the quality system underneath - ISO 9001:2015, IATF 16949:2016 (product design excluded) and ISO 14001:2015 certified is the kind of base you should see stated in writing.
And treat logos with suspicion. Read the certificate, check its scope and the site it covers, and confirm the certification is current. Then ask for the harder evidence: a sample first-article report, a change-notification procedure, and a copy of the last non-conformance record. Those three documents tell you more about aerospace readiness than any badge on a website.
Why does surface finish matter more on an aerospace part?
Finish on an aerospace part is rarely about looks. Machined surfaces sit in fatigue-sensitive load paths, seal faces, and threaded interfaces where a stress raiser or a burr is a functional defect. The practical bands are familiar from precision machining: finish-milled or turned faces typically land between Ra 0.8 and Ra 3.2 µm, and precision-ground surfaces reach down toward Ra 0.2-0.8 µm.
Secondary processes complicate the story. Anodizing, passivation, plating, and shot peening all change the surface after the tool leaves it, so a drawing that demands Ra 0.8 µm after anodizing is a different job from one that expects it straight from the machine. State in the notes whether the roughness value applies before or after finishing, and remember that edge conditions matter - call out burr removal explicitly on any feature that sees assembly or fluid.
Specify finish by function rather than by habit. The faces that slide, seal, or carry load deserve a real Ra number and the inspection to prove it; the faces that only hold a label do not. That discipline keeps the surface-finishing spend where the part needs it.
How do you qualify an online CNC machining supplier for an aerospace program?
- Send a real drawing and ask for a technical review. A shop that responds with questions about datums, alloy condition, and corner radii is reading the part. One that answers only with a price is quoting a shape.
- Ask for the documentation package before you commit. Request a sample first-article report and the material certificate format so there are no surprises at the first gate.
- Probe material control. Ask how incoming alloy is verified, how heat numbers are linked to finished lots, and how long records are kept.
- Check the quality system and its audit evidence. Read the certificate scope, then ask to see the inspection reports from the last lot the shop shipped.
- Run a small first lot before you scale. Inspect the records as hard as you inspect the parts; the paper trail is the deliverable that scales.
Qualification is a loop, not a single audit. First lot, review the FAI and the material certificates, then release a larger batch and compare the documentation quality on both. Within two cycles you will know whether the supplier treats aerospace documentation as a cost or as a capability.
Frequently Asked Questions
Do aerospace parts need tighter tolerances than ±0.003 mm?
For milled and turned features, ±0.003 mm is the realistic production envelope, and ±0.002 mm is achievable on precision-ground surfaces. Capability on key characteristics at Ppk ≥ 1.67 initial matters more than a headline number, because it is what keeps the process passing order after order.
Which material certificate should I request on an aerospace part?
Ask for a mill certificate in the EN 10204 3.1 style, naming the heat number, the alloy, and the mechanical test results. The heat number must match the stock used for your lot and should be attached to the first-article report on the first order.
What is the difference between 7075 and 2024 aluminum for a machined part?
7075 offers higher strength and is the default for structural brackets; 2024 offers better toughness and fatigue resistance but lower corrosion resistance and usually needs protection. Specify the temper and the surface treatment, and let the qualification data, not the brochure, make the final call.
Can titanium parts be machined reliably through an online CNC machining service?
Yes. Ti-6Al-4V machines consistently when the shop uses rigid fixturing, sharp tooling, and realistic speeds. Expect longer cycle times and a higher price than aluminum; require the same material certificate and FAI data as any other aerospace alloy.
Is AS9100 certification required to machine aerospace parts?
Aerospace primes commonly expect suppliers to operate under or align with AS9100, but the requirement is set by your contract and supplier agreement, not by the industry in general. Verify the shop documentation and change control in practice, and check the base certifications - ISO 9001:2015, IATF 16949:2016 (product design excluded) and ISO 14001:2015 - underneath.
What surface finish should flight-critical machined features carry?
Sealing, sliding, and fatigue-sensitive faces are commonly specified between Ra 0.8 and Ra 1.6 µm after machining, with ground surfaces reaching lower. Call out the value by function and state whether it applies before or after any coating or finishing step.
What should the first-article report include for an aerospace first lot?
It should cover every feature on the drawing, measured against the datum reference frame, state the drawing revision and material heat number, and attach the certificate for the lot. If the report cannot be mapped feature by feature to your drawing, the process has not been demonstrated.
Have an aerospace drawing that needs a documentation review?
Upload the part file with your material and certificate requirements and ask for a technical review before you commit. Contact the Online CNC Machining team to start the conversation.
